广西南宁市蓝添化工有限公司

Headquarter: Chemical Industry Park, Economic Development Zone,  JiNan City,  ShanDong Province, China.

Phone +86-152 8958 7728

Angela@BlueSkytcca.com
Magazine cover

Advancing High-Energy-Density Devices – Tech Briefs

Software
Communications
Lighting
Electrical/​Electronics
RF & Microwave Electronics
Semiconductors & ICs
Energy
Photonics/​Optics
Imaging
Motion Control
Robotics, Automation & Control
Test & Measurement
Sensors/​Data Acquisition
Manufacturing & Prototyping
Materials & Coatings
Mechanical & Fluid Systems
Propulsion
Transportation
Automotive
Magazine cover
Current Issue
Magazine Archives


Taiyuan University of Technology, China
The portable and electric energy storage market has long been dominated by lithium-ion batteries and supercapacitors, surpassing other energy storage systems in their ability to provide higher energy and power. However, in critical applications such as electric vehicles, there is a growing demand for a device that can efficiently produce both high power and high energy over a significant number of cycles. Meeting these rigorous standards presents new challenges for existing technologies, prompting researchers to explore alternative technologies for energy storage devices.
A promising strategy is to modify the high-conductive hard carbon anode, which exhibits excellent structural stability, to match it with an activated carbon cathode, thus creating a dual-carbon LIC (lithium-ion capacitor). In this study, a one-pot in-situ expansion and heteroatom doping strategy was employed to prepare sheet-like hard carbon, while the activated carbon was obtained through activation processes.
“However, ion kinetics mismatch between cathode and anode can lead to unsatisfied cycling lifetime and anode degradation,” explained Yingxiong Wang, corresponding of a new study that addressed this limitation. “We used a special method to create two types of carbon materials: sheet-like hard carbon and activated carbon.”
Wang and his co-workers used ammonium persulfate to help expand and modify the hard carbon, making it better for use in batteries. The carbon materials, known as FRNS-HC and FRNS-AC, were made from furfural residues, which are leftovers from a natural substance. They were then tested in Li-ion batteries.
“The results were impressive – when FRNS-HC was used as the negative part of the battery, it could store 374 mAh g-1 at low power level, and 123.1 mAh g-1 at a higher power level,” shared Wang. “When combined with a special porous carbon material as the positive part of the battery, the whole battery showed a high specific energy of 147.67 Wh kg-1, with a power output of about 199.93 W kg-1.”
Notably, the battery also lasted a very long time, with almost no loss in performance even after being charged and discharged 1,000 times. The team published their findings in the KeAi journal Green Energy & Environment.
“We recommend the use of bio-mass-based raw materials as carbon precursors, along with efficient and eco-friendly synthesis techniques,” said Wang. “This study offers a promising approach to create heteroatom-doped porous carbon from biomass waste, and it holds great potential for advancing high-energy-density devices.”
For more information, contact Ye He at This email address is being protected from spambots. You need JavaScript enabled to view it.; 521-098-1577.
This article first appeared in the September, 2023 issue of Battery & Electrification Technology Magazine.
Read more articles from this issue here.
Read more articles from the archives here.

DNA Combined with Glass Results in a Stronger, Lighter Material
New Material Will Burn Viruses, Not Skin
Here’s an Idea: The Gripen E Jet’s New Li-ion Battery
4D Printing with Smart Materials
Learning to Control a Robot
Using Coffee to Reduce Waste from 3D Printing
Miniaturized Solutions for Battery Development
Engineering Processes for Digital Knowledge Workers
Accelerate Electric Vehicle Development with HPC and Unified Design and Simulation
How Additive Manufacturing Can Increase Efficiency in EV Production
October Battery & Electrification Summit
High Optical Power SOA and DFB Lasers for High Performance Photonic Systems
About
Medical Design Briefs
Mobility Engineering Technology
By submitting your personal information, you agree that SAE Media Group and carefully selected industry sponsors of this content may contact you and that you have read and agree to the Privacy Policy.
You may reach us at privacy@saemediagroup.com.
You may unsubscribe at any time.
Subscriber Services
Feedback
Contact Us
Site Map
Advertise
Privacy Policy
Cookie Usage

© 2009-2023 SAE Media Group

source

Leave a Reply

Your email address will not be published.

*